Anti-static mat
There are two main types: normal type and anti-fatigue type.
Anti-static anti-fatigue mat is suitable for anti-static work places that need to stand for a long time. Anti-static mats can effectively cushion foot pressure and relieve fatigue.
Function: vent the static charge of the human body to prevent static electricity from causing harm.
Method: Through the grounding system.
Features: Easy and quick to lay.
Flat and tough.
Permanent anti-static.
Fold and edit this paragraph anti-static mat (common type)
Material:
It is mainly made of a variety of processes using conductive materials, static dissipative materials and synthetic rubber.
structure:
It is generally a two-layer structure.
The surface layer is a static dissipative layer (thinner, 1/4 thickness), and the bottom layer is a conductive layer (thicker, accounting for 3/4 thickness). performance:
It is durable and has good acid, alkali and chemical resistance.
And wear-resistant, easy to clean.
Surface layer:
10^6-10^9Ω, the color is green, gray, blue.
Can be divided into matt and bright.
Bottom layer:
10^3-10^5Ω, the color is black.
specification:
It is mostly 2mm thick, 10m long, and has a width of 0.6m/1.0m/1.2m.
use:
Industrial production workshops and advanced laboratories for electronics, semiconductors, computers, communications equipment and integrated circuits.
Folding and editing this paragraph anti-static anti-fatigue mat
Introduction:
Anti-static anti-fatigue mat is suitable for anti-static work places that need to stand for a long time. Anti-static mats can effectively cushion foot pressure and relieve fatigue.
structure:
Two-tier structure:
The upper layer is anti-static PVC/conductive rubber.
The lower layer is a urethane resin foam.
Three-tier structure:
The upper layer is anti-static PVC/conductive rubber.
The middle layer is EPDM (or urethane resin) foamed cotton.
The bottom layer is a conductive rubber.
performance:
It is crafted with advanced technology to meet the requirements of modern people's work comfort.
1, can be permanently anti-static.
2, flexible, strong rebound, easy to clean, easy to move.
3, the surface is steel pattern or spherical pattern anti-skid design, the use is safer.
4, can withstand acid and alkali solvents.
Surface resistance:
Static dissipative layer 10^8Ω-10^9Ω
Conductive layer 10^3Ω-10^5Ω
Customizable specifications:
It is 400-15000mm long, 400-1220mm wide and 15/17/20/25mm thick.
Can be made into small pieces or strips to suit single or assembly lines.
The surface color is all black or black with a yellow edge.
Optional grounding buckle or anti-static warning sign.
Folding and editing method of laying anti-static floor mat of this paragraph
1. Basic ground requirements:
1 The basic ground can be water-grinding ground, porcelain ground, and wooden ground.
2 The ground should be flat, no obvious unevenness, and the unevenness should be less than two thousandths.
3 The ground needs to have sufficient strength, no sanding and shelling. 4 The ground needs to be dry. </p>
2. Construction procedures and specific methods:
1 Wash the impurities on the ground with 120# gasoline or xylene (with a washing machine);
2 For the laying of copper strips or aluminum strips on the ground, if the thickness of the copper strip is 0.02mm and the width is 30mm, the number of strips is determined according to the actual requirements of the ground laying, and the end of the laying copper strip is led to the ground.
3 After laying the grounding conductive mesh, clean and dry the floor, apply conductive glue, dry for 20-30 minutes, until the hand is not sticky, the bottom of the anti-static mat (black surface) is the same (coating conductive glue once), then The anti-static rubber sheet is bonded to the ground, and then rolled by a heavy roller for 5 times to make the surface of the anti-static rubber sheet neat and straight, and can be used after 48 hours at normal temperature.
4 The ambient temperature requirement during construction shall not be less than 25 degrees Celsius and the humidity shall not be greater than that of ventilation.
5 Conductive glue liquid resistance coefficient is not more than 108Ω, peeling strength Kg/2.5cm.
6 Conductive between the gaps, can be coated with conductive glue, or paste on the surface of the copper strip